5G NTN关键技术研究与演进展望

5G非地面网络（non-terrestrial network,NTN）技术是5G通信系统面向卫星通信和低空通信等新应用场景的重要技术，标志着5G技术应用从陆地通信走向了空间通信。首先分析了5G NTN和地面5G的差异点，包括网络架构、时频同步、HARQ和移动性管理等。进而介绍了3GPP Release 17的5G NTN标准进展及关键技术点与3GPP Release 18的5G NTN增强技术。最后展望了未来空、天、地一体化的技术演进。通过对5G NTN技术研究和标准分析，明确了5G和卫星通信融合的技术路线，并为后续6G空、天、地融合系统研究和设计提供基础。     

Influence of selenium growth condition on the photovoltaic conversion efficiency of Sb2Se3 as the solar cell absorption layer

Journal of Materials Science: Materials in Electronics - The influences of the selenium (Se) growth condition on the electronic level structure including deep defects and further on the...     

Co-precipitation synthesis of ZnAl2O4: Cr3+ phosphor for better light penetration in pc-LED

Cr doped ZnAl₂O₄ spinel samples were prepared by the traditional solid state reaction and co-precipitation synthetic route, and the results suggest that the co-precipitation method has some superiority in contrast to the solid state reaction method. XRD, FT-IR, and XPS spectra confirmed that the well-crystallized spinel cubic phase of ZnAl₂O₄: Cr³⁺ samples were successfully formed. The morphology of the samples was investigated by FE-SEM and FE-TEM, and the results show that the samples by the co-precipitation route can generate a smaller size of particles compared to the solid state reaction. Photoluminescence excitation spectra monitored at 686 nm are comprised of two broad excitation bands near 530 nm and 395 nm, and the emission spectra show emissions ranging from 640 to 780 nm, due to the ²E?→?⁴A₂ spin-forbidden transition of Cr³⁺ ions in spinel lattices. The optimized concentration monitored at 686 nm is 1%, while at 693 nm is 3.5%. Compared with the samples by solid state reaction method, the samples by co-precipitation method show preferable luminescent properties, such as the higher photoluminescence intensity and higher quantum efficiency. Several phosphor-converted LEDs were to investigate the applicability of the prepared samples. The results confirm that the phosphor has potential applications in plant growth and supplementing the red region in white-LEDs and the phosphors prepared by co-precipitation are more suitable to be used in phosphor-converted LED devices due to their preferable luminescent properties.

     

双酚芴环氧树脂体系热性能和粘接性能研究

环氧树脂是一种性能优异的热固性树脂，在结构胶粘剂和纤维增强复合材料领域应用广泛。但是常见的环氧树脂体系耐热性普遍较差，近年来，航空航天领域对材料的热性能提出了更高的要求，常规的环氧树脂体系已经无法满足耐高温需求。针对该问题，我们设计了一种耐热性较高的双酚芴型环氧树脂体系，并对其热性能和粘接性能进行了研究。在本文中，首先采用流变学方法和DSC研究了其工艺性能，使用DMA和TGA法分析了环氧树脂体系的耐热性能，并通过单搭接剪切试验测试了该环氧体系的粘接性能。结果表明，双酚芴型环氧树脂体系可在180℃固化，固化后的玻璃化转变温度达到190℃，失重5%时的温度为392℃，150℃时的剪切强度为5.8 MPa，展现了优异的耐热性能和粘接性能。     

基于超声导波SC-DTW的金属板微损检测方法

针对金属板材的质量控制与服役性能评估问题,在对金属板材微损伤进行超声导波检测的基础上,结合形状上下文(shape context,SC)与动态时间规整方法对其损伤劣化程度进行量化评估.该方法以无损Lamb波信号为基准,采用动态时间规划(dynamic time warping,DWT)算法对损伤信号进行相似匹配分析对比,确定基准信号与损伤信号的最佳匹配路径.引入SC的轮廓识别方法对Lamb波的局部波形信息进行统计分析,以波形形状距离代替传统欧氏距离匹配方法,解决DTW相似匹配中的病态对齐问题.最后,将无损Lamb波与损伤Lamb波信号间SC-DTW匹配距离作为损伤程度的量化指标,采用随机闭合裂纹的有限元仿真模型和铝板弯折实验对所提出方法进行验证,结果表明,基于Lamb波SC-DTW的损伤量化指数对铝板早期裂纹具有较高的敏感性和较好的量化表征能力.该方法无需对波包进行识别,也不必进行复杂的特征提取,具有简单高效和抗噪声能力强等优点,在金属板服役性能评估与质量控制中有较好的实用性和推广价值.     

基于Massive MIMO及频谱叠加的5G SA网络上行优化方法

大规模多输入多输出(Multiple-Input Multiple-Output, MIMO)可以有效提升5G SA网络的上行链路数据传输速率以及可靠性。针对5G SA网络上行链路速率和覆盖不均衡的情况,提出了基于大规模MIMO的分组算法,将发送信号矢量进行分组,组内采用最大似然检测,组外采用基于正交三角分解(QR分解)的干扰消除检测,并且结合5G频谱的叠加策略,在降低算法复杂度的同时,有效提升网络覆盖和速率。通过5G SA现网实测,通过MIMO降低分组数量能够提升分组检测性能,结合上行低频段频谱叠加策略能够有效提升5G SA网络上行覆盖30%,提升5G SA网络上行平均速率40%~80%,特别是弱覆盖边缘的网络速率,最高可达600%。